All

Teach You How to Choose a Good Shade Sail? For most installations, you will use a eye screw on each corner of the shade sail. Which size screwdriver you will use depends mainly on the size of the shade sail. You will also need a mounting point (eg eye bolt). There is no one hardware package that fits all installed specifications. Check the hardware page of our website to determine the software required for installation. Why is the perimeter of the shade sail curved? That's when we deliberately cut an arc around the shade sail to pull the fabric tightly in the center of the sail when the sail is tensioned. Without these curved shadow sails will not be properly tensioned, nor will they be tensioned.Are the UVR and shading factors of all colors the same? will not. Generally, darker shades of color block more sunlight and ultraviolet light and provide more shadows. Most shade sails will block 90-95% of UV-A and UV-B rays. Is your shade sail hardware AISI316?AISI316 is the American designation for stainless steel 316, not an industry standard. As long as the element standard of stainless steel 316 is met, all are qualified 316. The specific 316 material standards are as follows: 316 composition is 06Cr17Ni12Mo2 06 represents C content, degree Cr content is 17%, Ni content is 12%, Mo content is 2% Generally, the higher the Ni content, the higher the price of stainless steel. American ASTM 316 is the same as the national standard 06Cr17Ni12Mo2. 316 stainless steel, due to the addition of Mo, so its corrosion resistance, atmospheric corrosion resistance and high temperature strength are particularly good, can be used under harsh conditions. What is the difference between UVR and Shade Factor? The shadow coefficient refers to the amount of shadow to be cast, and the UVR is a measure of how much harmful radiation is reduced.

TERADA HARDWARE QUALITY CONTROL First Test--product test When the products are making ,our worker will test the products dimension to control the tolerance Second Test--dimension test We will test material and dimension by QC department before packing. Every plastic bag will weight to ensure the quantity. Every carton will weight to second ensure. Third Test--mass products test Before shipment,we will check the packing,label and total weight RIGGING HARDWARE Terada rigging hardware have shackle, turnbuckle, wire rope clips, wire rope thimble, snap hook, lifting hook and other type hardware, we also support OEM products, we could follow your requirements to make products. CABLE RAILING Terada cable railing line have terminal turnbuckle, swage stud, swage terminal, swageless terminals, Anglewasher and other cable railing hardware. TENSILE STRUCTURE Tensile hardware is inclued shade sail fitting and other wire rope fittings,such as wire rope, cable stud, tensile turnbuckle, wire rope D ring. CNC HARDWARE Professional manufacturer of asphalt machines. Our sales and R&D team have over 10 years’ experience to focus on asphalt distributor, synchronous pavement surface vehicles and other road machinery and equipment. Based on innovation

How use wire rope clamp in right way? Precautions for use of the wire rope clips: it cannot be used for a long time, it should be inspected and scrapped regularly, and it cannot be used repeatedly.(1) The size of the wire rope clamp should be suitable for the thickness of the wire rope. The inner clearance of the U-shaped ring should be 1 to 3 mm larger than the diameter of the wire rope. If the clear distance is too large, the rope cannot be clamped easily. (2) When in use, tighten the U-bolt until the wire rope is flattened by about 1/3. As the steel wire rope deforms after being stressed, the rope must be tightened a second time after the steel wire rope is stressed to ensure the joint is secure. If it is necessary to check whether the rope card is slipping after the wire rope is stressed, an additional safety rope card can be used for this. The safety rope card is installed about 500mm from the last rope card. After releasing the rope head for a safety bend, it is clamped with the main rope. If the clip slips, the safety bend will be straightened, which is easy to find and reinforce in time. . (3) The arrangement interval between rope cards is generally about 6 to 7 times the diameter of the wire rope. The rope cards should be arranged in order. The U-shaped ring should be clamped on the side of the rope head, and the pressure plate should be placed on the side of the main rope.(4) Correctly arrange the quantity and method:The number of rope clips is generally not less than 3-5. The spacing between rope clips should be ≥ 6 times the wire rope warp. The distance between the last clip and the rope head should be ≥140mm.There are 3 ≤18mm,18-26mm set of 4,26-36mm set of 5,36-44mm with 644-60mm set of seven. (5) Wire rope rope clamp should be used together. When the rope diameter is below 19mm, the rope clamp should not be less than 3, and 19-32mm should not be less than 4. The arrangement interval between rope clamp is generally about 6 to 8 times the diameter of the wire rope. To arrange the rope clamp in order, the U-shaped ring should be clamped on the side of the rope head, and the pressure plate should be placed on the side of the main rope.After the wire rope clip is loaded once or twice, it should be checked for looseness. In general, the nuts need to be tightened further.(6) Pay attention to the following two points when using:a) The size of the clamp should be suitable for the thickness of the wire rope. The inner clearance of the U-ring should be 1-3mm larger than the diameter of the wire rope. If the clear distance is too large, the rope should not be clamped, which is prone to accidents. b) Be sure to tighten the bolts when tightening the chucks until the rope is flattened by 1 / 3-1 / 4 diameter. After the rope is stressed, tighten the chuck bolts again to ensure the joint is firm and reliable. c) The chucks should be arranged in a straight line. The U-shaped part should be in contact with the rope head and not the main rope, as shown in Figure a. If the U-shaped part is in contact with the main rope, after the main rope is squashed, the force is easy to break. d) In order to easily check whether the joint is reliable and find out whether the wire rope is sliding, you can press another chuck about 500mm behind the last clip and release the rope head with a "safety bend". As shown in Figure b. In this way, when the wire rope of the joint slips. The "safety bend" was first straightened, and measures should be taken immediately. JIS Type Wire Rope Clamp Material: SS316,SS304, IronProcess: Casting and ForgedAppication: Use for wire rope Casting U Clip DIN741 Material: SS316,SS304, IronProcess: Casting and ForgedAppication: Use for wire rope  Duplex Wire Rope Clip Material: SS316,SS304, IronProcess:  ForgedAppication: Use for wire rope

How to choose suitable you stainless Turnbuckles for your project? Rigging turnbuckle can be used to apply tension to wire rope or cable. Which composed of a  body and two end fittings. The end fittings have eye and eye, eye and hook, hook and hook, jaw and jaw, jaw and eye. Difference size rigging turnbuckle have difference thread diameter.The thread diameter refers to the diameter of the threaded portion of the end fittings. Large thread dimension will have a larger load carrying capacity than smaller. Turnbuckle Adjustment Turnbuckle have a opened length and closed length.Due to turnbuckle have two end parts. One is left hand thread, another is right hand thread. This design feature ensure only the turnbuckle body twists when you want to adjust the length.  Some end add a nut to fix the thread, which could ensure when your adjust the length into suitable position which can not move. The design add the safety of the construction. Difference end fittings will suit difference application. Each fittings have its own purpose, advantages and disadvantages.Eye end turnbuckle are sued with other fittings than can not be opened and connect into the eye such as D shackle, anchor shackle,snap hook and so on. whose link depend the link hardware. Due to eye end turnbuckle can not be opened, so which will be more safety.Jaw end turnbuckle are composed of a jaw, bolt, and pin. These are used to link other hardware and fittings which could be opened. Such as Stainless eye bolt&nut, link chain, wire rope thimble and so on. Considering big size turnbuckle need big working load limit, so big size jaw turnbuckle will choose nut to replace pin.Hook end turnbuckles are used for connecting temporary link. It could easy attached and detached from other link components. When you choose hook end turnbuckles, maybe you could worry the safety. Pls not worried. Due to the hook end turnbuckle working load limit will bigger than attached other fittings, so which could safety. Eye and Eye Turnbuckle Jaw and Jaw Turnbuckle Hook and Hook Turnbuckle

Payments Terada can accept payment methods in a variety of terms. The most commonly used ones are T/T, L/C.For T/T We usually pay 30%-40% in advance, and settle the remaining balance before shipment.In addition, we will provide detailed shipping information and product details before shipment to ensure that customers have a macro understanding of every detail of the product. Please be assured that we are regular manufacturers and sincerely do business with you.

Delivery Time Terada Hardware's normal delivery time is 30 days, but if the quantity of products is relatively large, it is usually 45 days.Of course, if you catch up with the peak production season, the delivery time will be extended. However, please be assured that we will give you a satisfactory delivery date on the basis of quality assurance, if you have urgent procurement. We are also happy to cooperate with you and strive to give you the best delivery time. If you have any questions, you can communicate with us in time via email, we will usually give you an answer within 24 hours.

How to deal with stainless steel chain rust? There is one item on the rigging that is often overlooked, but there are very important parts, that is the lifting chain. When the equipment is used for a long time, each component will tend to age or gradually fail. The rigging is also the same with stainless steel chains. The more common is the corrosion of the chain. In addition to the time relationship, what other reasons lead to similar problems?1, the rigging with stainless steel chain rust because of the lack of anti-rust treatmentIn the production process of the lifting chain, the operator does not strictly carry out the anti-rust treatment according to the production requirements, and does not use the anti-rust packaging. Once it comes into contact with the corrosive liquid gas, the corrosion will occur. .2. The stainless steel chain of the rigging is related to the chain material.In order to reduce the production cost of the hoisting chain, some manufacturers choose unqualified materials, such as the high content of non-metallic impurities in the steel, which makes the rust resistance of the formed chain itself reduced, resulting in similar defects.3, rusting of stainless steel chain rigging is caused by the quality of anti-rust oil is not up to standardEven if rust-proof lubricants and cleaning oils have been applied to the lifting chain, if the quality of the products does not meet the technical requirements, it will be in vain, which will also cause rusting of the lifting chain.4. Corrosion of stainless steel chain in rigging is related to operating environmentWhen the rigging is operated with a stainless steel chain for a long period of time in a poor condition, it is considered that the harmful substance content is too high, or the space is too small to be rust-proofed, thereby adversely affecting the chain.Although it is a stainless steel chain, once our stainless steel chain is often in a humid environment, or encounter other liquids that are corrosive, etc., our stainless steel chain will have more or less rust spots. So how do we deal with the rust phenomenon of stainless steel chains?The use of pickling paste is a common method for removing stainless steel chain rust spots. Why is it so popular because it is a much smoother finish on the surface of the chain, and a passivation film is formed on the surface of the chain, so that our stainless steel chain The service life has also been extended. This method of descaling is suitable for most industries such as chemical machinery, food machinery, printing and dyeing machinery, pharmaceutical machinery, and pressure vessel manufacturing.The operation of using the pickling paste is also simple to tell everyone. The first is to apply our pickling paste on the surface of the stainless steel chain. Remember, at this time, our coating thickness is controlled between 0.5-2mm, time control. In 3-10 minutes or more, if the temperature is low in winter, or when it is below 0 °C or when the scale is thick, the time can be extended appropriately. In the process of this treatment, it is recommended to brush more times with a brush. After the scale of the surface of our stainless steel chain is completely removed, then the water can be used again, or the stainless steel chain can be washed with lime water or alkaline water. The purpose is to avoid rust.

Shackle The stainless steel shackle is a type of stainless steel rigging. The shackles commonly used in the domestic market are generally classified into three categories according to the production standard: the national standard, the American standard, and the Japanese standard; among them, the American standard is the most commonly used, because it is widely used because of its small size and large weight. According to the type can be divided into G209 (BW), G210 (DW), G2130 (BX), G2150 (DX). According to the type can be divided into bow type (omega type) bow type with female shackle and D type (U type or straight Type) D type with female shackle; according to the place of use can be divided into two types of marine and land.Scope of useThe shackle is widely used in electric power, metallurgy, petroleum, machinery, railway, chemical, port, mining, construction and other industries.Scrap standard1. There is obvious permanent deformation or the axle pin cannot rotate freely.2. The wear of any part of the buckle body and the shaft pin is more than 10% of the original size.3. Cracks appear in any part of the shackle.4. The shackle cannot be locked.5. Unsatisfactory after shackle test.Material and useAt present, the better shackles are generally full forging processes, and the shackle pull is good. Stainless steel shackles include general lifting shackles, marine shackles and general shackles. The weight is heavy and the volume is large, and it is generally not installed in a position that is not frequently disassembled. When choosing a shackle, pay attention to the safety factor, which is generally 4 times and 6 times. When using the shackle, the rated load must be strictly observed. Excessive use and overloading are not allowed.

How To Install Wire Rope Clamp with cable? The purpose of the wire rope clamp:First, stainless steel casting wire rope clips are commonly used for static bolting, rope cable fastening, such as power, communication lines, strapping and fastening.Forged steel wire rope clamps are often used for lifting and lifting load, such as various engineering lifting machinery, metallurgical mining equipment, oil field derrick, port railway loading and unloading, forestry machinery, electrical equipment, aviation and marine, land transportation, engineering rescue, salvage shipwreck , factory and mining enterprises lifting, hoisting, traction rigging.Stainless steel wire rope clips are used in marine fittings, chemical plants, radiation, etc. due to their corrosion resistance and rust resistance.Second, the characteristics: with the strength of the wire rope, the use of safety, the appearance of the beautiful transition smooth, lifting work safety load, can withstand the impact load, long service life. Wire rope clamp method and standard of use:1. When using the stainless steel clamp, it must be used in conjunction with the diameter of the wire rope.2. In order to protect the wire rope from wear, the top eye must in principle use a wire rope collar.3. At the end of each wire rope, three or more chucks should be used at the same time to obtain effective locking force. The spacing of each rope clamp should be 6-7 times the diameter of the wire rope.4. The wire rope clamp should be fastened to the working section of the wire rope. The U-shaped bolts are fastened on the tail section of the wire rope and should not be alternately arranged on the wire rope, as shown in the following figure: 5. It is necessary to consider the reasonable force of each rope clamp to fasten the rope clamp. The rope clamp farthest from the collar shall not be separately fastened first. The rope clamp (the first rope clamp) closest to the collar should be as close as possible to the collar, but the rope clamp must be properly tightened and the outer wire of the rope must not be damaged.6. The strength of the wire rope clamp is determined by the correct arrangement of the rope clamp on the wire rope and the caution and proficiency of the rope clamp fixing and clamping. Insufficient tightening of the nuts or wire rope clamps may cause the rope ends to slip when initially loaded. If the rope clamps are properly arranged and tightened according to the recommended number, and all the rope clamps will clamp the longer part of the rope, and the U-bolts are to the shorter or tail section of the rope, then the strength of the fixing is at least 80% of the strength of the wire rope itself. In the actual use, the clamp rope should be inspected after being loaded one or two times. In most cases, the nut needs to be further tightened.7. Stainless steel wire rope clamps are prone to lock-up due to stainless steel fasteners. When tightening nuts, the nuts should follow the anti-locking method of stainless steel fasteners. If necessary, use diesel or anti-locking oil for pretreatment.

Drill Holes for Cable Railings when you choose your prefer cable railing fittings to DIY your stair. Many be you will confuse how to Drill Holes for Cable Railing? Now we will show you how to drawing the hole.Drill holes in posts. Holediameter depends on cable size and type ofitting. See charts below. If you choose 1/8 cable railing fittings,you will drill like this. 1.Your purchasing is 1/8 quick link swagless terminals like picture TRD-01. You should drill 3/8 hole at front and 1/4 hole at back by electric drill. 2. If you choose is 1/8 hand swage stud,you need dill 3/8 hole at front and 5/16 hole at back by electric drill . If you considering the safety and choose 3/16 cable railing fittings,you will drill like this.1.3/16 Quick link swagless terminals like picture TRD-02,You should drill 9/16 hole at front and 1/4 hole at back by electric drill. 2.If you choose is 3/16 swage stud,you need dill 3/8 hole at front and 5/16 hole at back by electric drill . Terada Hardware main in stainless hardware more than 20 years. We make rigging hardware,cable railing,marine hardware and archtectural hardware. Welcomed OEM,samples and drawing.we could lower that cost and not compromise on quality.Our product quality is checked through strict quality inspections. To ensure that each product reaches the user’s hands are high-quality A-class products. All materials are selected as the best material production. Each order has a corresponding material test report. Our products are passed ISO9001 quality system certification and SGS third-party testing of qualified products. Products are exported to Europe and the United States, which has been the customer’s recognition and praise.

How to install the cable railing system? More and more private users prefer to install cable railing systems in their courtyards, balconies or stairs. Because of its simple appearance and low cost, it is in line with the most demanding aesthetics of the contemporary people, and is loved by the majority of users.First you need to prepare the relevant tools and hardware accessories. The installation of the wire cable is the main accessory, and according to your own preferences, you can choose the corresponding stainless steel hardware. Installation is very simple. As long as you follow our instructions, you can DIY your own work.Need to prepare the following tools and accessories:Cable crimping pliers2. Cable cutter3. Electric drill4. Suitable drill bit5.1/8 inch cable6.cable railing fittings1) DrillingDrill evenly spaced holes in the pre-fixed handrail. If using our 1/8" stainless steel cable (recommended for excellent strength and corrosion resistance), we recommend using a 3/16" hole. After the template is finished, use the drill and 3/16" drill on the column. Drill holes.2) Determine the required cable lengthDetermining the length of the cable requires a little math. You need to first determine the perimeter of the area where you want to place the cable railing, and then multiply by the desired rung or multiple strands:Total required cable = circumference X required number of strands3) Ensure cable levelAfter drilling all the holes in the column, it is best to ensure that the cables are parallel and level to each other. To do this, thread the rope through all the holes and adjust the tension until the rope is taught. Take a step back and redo the work once. If you are satisfied, please continue to the next step.4) Cut and terminate the cableUse steel wire rope scissors to cut the length of the required wire rope, and insert one end of the wire rope into the selected stainless steel hardware fittings, and press them with pressing pliers to ensure that the wire rope will not be pulled out from the hardware.6) Adjust cable tension and seal cableUse a hex tool to adjust the cable to the proper tension. It is necessary to have the slack of the cable and not to hang down.Repeat as described above until all cable railing is installed.